OPERATORS AND PARTS MANUAL NO. 07-2-V-FORCEManufactured byCounty Hwy. A WestP.O. Box 405Dorchester, Wisconsin 54425Phone 715-654-5132 • FAX 715-654-55
WARNING: HYDRAULIC FLUID ESCAPINGUNDER PRESSURE CAN HAVE SUFFICIENTFORCE TO PENETRATE SKIN. KEEP ALL HOSESAND CONNECTIONS IN GOOD SERVICEABLECONDITION
Operating speed is dictated by the terrain over whichyou are traveling. Always use caution. Avoid travelingon slopes or hills that are unsafe.WARNING:
Clean all manure from rear ends of augers, flow con-trol rear gate and spinners.WARNING: MAKE CERTAIN EVERYONE ISCLEAR OF THE SPREADER BEFORE APPLYING
OPERATIONLOADINGCAUTION: TO PREVENT DAMAGE TO AU-GERS, SPINNERS, AND DRIVE LINES, FOREIGNOBJECTS (STONES, CONCRETE, TIMBER, METALOR LARGEFROZEN CHUNKS
VERY IMPORTANT: THIS MACHINE IS NOT IN-TENDED TO BE A BALE GRINDER, HAY CHOPPEROR BEDDING MACHINE. LONG HAY OR STRAWMUST CONTAIN MANURE IN ORDER TO BE
side at a time. After first side is unloaded install boltsin opposite side and unload the remainder of thespreader. If a second shear has happened wit
PTO DRIVE LINEWARNING: BEFORE ATTEMPTING TO OP-ERATE THIS SPREADER, READ AND STUDY ALLSAFETY INFORMATION. IN ADDITION, MAKESURE THAT EVERY INDIVIDUAL
Adjust the drawbar at 13-17” above the ground. Ex-tend or shorten the drawbar so horizontal distancefrom end of tractor PTO shaft to center of hitch p
ADJUSTMENTSWARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULICPRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING TH
Model V-Force —2—This Page Intentionally Blank
Model V-Force —20—FIGURE 10. RH AUGER CHAIN DRIVESPRINGLOADEDADJUSTERIDLERNYLONROLLERROLLERCHAINFIGURE 11. LH AUGER CHAIN DRIVEIDLERNYLONROLLERSTRACKI
LUBRICATIONWARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULICPRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING TH
MONTHLY LUBRICATIONKeep the (3) gearboxes ½ full of liquid geargrease at all times, capacity approximately 30 oz.Check regularly for any observable le
Model V-Force —23—L2A1L1COVERLUBRICATION & ADJUSTMENT FOR 3RD AUGERWEEKLY LUBRICATION (every 25-30 loads))Grease (1) bearing supporting the front
INSTRUCTIONS FOR AUTOMATIC CHAIN OILERWARNING: DISCONNECT PTO DRIVESHAFT AND HYDRAULIC HOSES (RELIEVE HY-DRAULIC PRESSURE) BEFORE CLEANING, AD-JUSTING
Model V-Force —25—This Page Intentionally Blank
Model V-Force —26—OIL-KIT35REPAIR PARTS
Model V-Force —27—KEY PART NO. OEM PART NO. DESCRIPTION1 952-0001-1-33 170-4515 Holder, Manifold Valve Assembly2 952-0001-1-27 576895 Sleeve Nut Brass
Model V-Force —28—FRONT SHIELD & SIDE SHAFT DRIVEKEY PART NO. DESCRIPTION1 914-3801 1-3/8" Pillow Block Bearing2 910-0013 80B18 Sprocket 1-3/
Model V-Force —29—AUGER DRIVE, PRIMARY REDUCTIONKEY PART NO. DESCRIPTION1 933-3628 Copper Tube Grease Line25" (includes zerk, fittings)2 38-0013
TABLE OF CONTENTS ...
Model V-Force —30—AUGER DRIVE, SECONDARY REDUCTIONKEY PART NO. DESCRIPTION1 14-0031 Bearing, 4 Bolt, 2" Bore2 38-0013 Roll Pin, 5/16" x 1-3/
Model V-Force —31—RH AUGER DRIVE, FINAL REDUCTIONKEY PART NO. DESCRIPTION1 33-0025 2-1/2" Retaining Ring2 910-0064 Welded Sprocket Assy, LH,80A60
Model V-Force —32—LH AUGER DRIVE, FINAL REDUCTIONInstall (#120-72) Roller Chain, Key #21W/Connector Link Cotter Pins FacingTowards RearOf Spreader.
Model V-Force —33—KEY PART NO. DESCRIPTION1 14-0031 Bearing, 4 Bolt Flange, 2" Bore2 925-3873 Front Bearing Mounting Plate3 910-0064 Welded Sproc
Model V-Force —34—BOX, AUGERS & SIDE SHAFT
Model V-Force —35—KEY PART NO. DESCRIPTION1 901-3903 Main Welded Body, 7500901-3915 Main Welded Body, 74002 901-3801-82 Adj. Hitch Plate, 1” Pin3 923-
Model V-Force —36—UNLOADING GATE & TRIP PAN DOORSPRIOR TO 08 S/N’SPRIOR TO 08 S/N’SPRIOR TO 08 S/N’S
Model V-Force —37—KEY PART NO. DESCRIPTION QTY1 925-5005 Spinner Deflector Welded Assy. 12 901-3903-34 Spinner Mount Channel 23 949-3753 Poly Gate Sli
Model V-Force —38—SPINNERS & GEARBOX SHAFT DRIVEPADDLE OPTIONS
Model V-Force —39—KEY PART NO. DESCRIPTION1 901-3753-10 Spinner Paddle, 2 Per Spinner2 901-3753-19 8865/7000 LH Aggressive Spinner Paddle3 19-0041 Gea
Model V-Force —4—NEW MEYER SUPER SPREADERMANUFACTURER’S WARRANTYI. The “Product Registration & Inspection Certificate” along with the original bil
Model V-Force —40—KEY PART NO. DESCRIPTION1 19-0022-1-PF Splined Pinion Output Shaft/Gear Assy2 19-0018-2 Seal3 19-0018-3 Bearing Cone4 19-0016-3 Bear
Model V-Force —41—HUBS, AXLE & TANDEM AXLE ASSEMBLYKEY PART NO. DESCRIPTION7500 74001 75-0207 75-0205 Hub Assembly Complete2 75-0207-2 75-0205-2 S
Model V-Force —42—THIRD AUGER
Model V-Force —43—KEY PART NO. DESCRIPTION1 929-3601 Extension Spring2 35-0008 ½"x1/2"x2" Square Key3 910-0050 80B26 Sprocket 2" B
Model V-Force —44—918-0212 PTO DRIVE SHAFT ASSEMBLY(PRIOR TO SERIAL #SV087500201)918-0312 PTO DRIVE SHAFT ASSEMBLY(SERIAL #SV087500201 & LATER)540
Model V-Force —45—KEY MEYER PART NO. DESCRIPTION1 918-0208-2-3-2 Housing2 918-0208-2-3-3 Hub3 918-0208-2-3-4 Spring Pack 1900NM4 918-0208-2-3-5 Washer
Model V-Force —46—1000 RPM KITSVS-RPM-KITKEY PART NO. DESCRIPTION QTY.1 19-0002-17 Vent Plug 12 29-0015 Tightener Spring 13 33-0012 Retaining Ring 1-1
Model V-Force —47—KEY MEYER PARTNO.DESCRIPTION1 918-0208-1-1 Yoke 1-3/8"-21 Splined As-sembly-Standard918-0210-1-1 Yoke 1-3/4"-20 Splined As
Model V-Force —48—918-0209 PTO DRIVE SHAFT ASSEMBLY1000 RPM 1-3/8” 21 SPLINE (STANDARD)918-0211 PTO DRIVE SHAFT1000 RPM 1-3/4” 20 SPLINE (OPTIONAL)CUT
Model V-Force —49—KEY MEYER PARTNO.DESCRIPTION1 918-0208-1-1 Yoke 1 3/8"-21 Splined As-sembly-Standard918-0210-1-1 Yoke 1 3/4"-20 Splined As
Model V-Force —5—INTRODUCTIONCongratulations on your purchase of a new Meyerfarm equipment product. Undoubtedly you have givenmuch consideration to yo
Model V-Force —50—KEY MEYER PART NO. DESCRIPTION1 918-0208-2-3-2 Housing2 918-0208-2-3-3 Hub3 918-0208-2-3-10 Spring Pack 2100NM4 918-0208-2-3-5 Washe
Model V-Force —51—V-MAX HIGHWAY LIGHTING15KEY PART NO. DESCRIPTION QTY1 56-0030 Dual Light LH w/4-Plug 11a 56-0030-TR Truck Mount Dual LightLH w/4-Plu
Model V-Force —52—MEYER SUPER SPREADER“TROUBLE SHOOTING”SYMPTOM PROBLEM SOLUTIONAUGERSAugers shake or chatterAugers wobble/lift up & downStiff rol
Model V-Force —53—MEYER SUPER SPREADER“TROUBLE SHOOTING”SYMPTOM PROBLEM SOLUTIONROLLER CHAINSAND SPROCKETSExcessive chain wearRoller chain breakageSpr
Model V-Force —54—MEYER SUPER SPREADER“MAINTENANCE RECORD”Model No. ____________________Serial No. ____________________Delivery Date: ________________
Model V-Force —55—MEYER EQUIPMENT WHEEL TORQUEBOLT/STUDSIZESOCKETSIZEPRESS FORMEDWHEEL CENTERBOLTTYPEHEAVY DUTYWHEEL CENTER½ 3/4 80 ft lbs Lug Bolt 85
Model V-Force —56—Farm Equipment Buyers Trust the Name Meyer!MEYER SUPER SPREADER“SPECIFICATIONS”V-Force 7400Trailer ModelV-Force 7400Truck MountV-For
Model V-Force —57—V-Force 7400Trailer ModelV-Force 7400Truck MountV-Force 7500Trailer ModelV-Force 7500Truck MountThickness -Front/Back Panel3/16” 3/1
Model V-Force —58—This Page Is Intentionally Blank
Model V-Force —59—Manufactured by:Meyer Mfg. Corp.County Hwy. A WestP.O. Box 405Dorchester, Wisconsin 54425-0405Phone 715-654-5132 • FAX 715-654-55131
Model V-Force —6—SAFETY PRECAUTIONSThis symbol is used to call attention to instructions concerning personal safety. Be sure to observeand follow thes
c
Model V-Force —7—GFCBEDHIKBLSEE DECALS ON PAGE 8.CAUTION: READ ALL DECALS ON THE SPREADER AND IN THIS MANUAL. KEEP THESE DECALS CLEAN ANDREPLACE ANY L
Model V-Force —8—SAFETY FIRSTThe Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader arevarious decals t
PRE-OPERATIONThis spreader is to be operated with 540 RPM PTO only,unless the spreader is 1000 RPM equipped. The hitch ofthe spreader is designed for
Comments to this Manuals